The cable set SMPS1200 is a complete set of cables to connect the SMPS1200A180, SMPS1200A400 or the SMPS1200A700
3 pole male XLR cable connector from Neutrik with black metal housing and gold plated contacts.
The cable set loudspeaker FA 1 way is a complete cable set to connect your 1 way Fusion Amp with your loudspeaker. This is the same loudspeaker cable set as supplied with new Fusion Amps.The length of the cable is 125cm.
The cable set loudspeaker FA 3 way is a complete cable set to connect your 2 or 3 way Fusion Amp with your loudspeaker. This is the same loudspeaker cable set as supplied with new Fusion Amps. The length of the cables is 125cm.
Neutrik Speakon NL4MP to connect your amplifier or other device to your speakers.
50cm balanced signal cable with 4-pin connector also providing the enable signal. Specifications The QuietConduit cable design incorporates several refinements over normal balanced cables. A conductive polymer interface layer between the braid shield and the insulation of the signal conductor short-circuits triboelectric currents where they are generating, virtually eliminating microphonic noise pickup. A secondary benefit of this layer is to improve the electrostatic shielding effectiveness of the braid shield. Another crucial improvement is the elimination of drain wires, which is normally included for ease of termination but which allow shield currents to couple noise asymmetrically into the signal conductors. The geometry of the QuietConduit cable is precisely controlled, insuring that any noise coupling is strictly limited to common mode.
3 pole male XLR cable chassis plug from Neutrik with black metal housing and gold plated contacts.
The cable set SMPS3k is a complete set of cables to connect the SMPS3k to one amplifier module. If you want to connect 2 or 3 amplifiers you'll need 2 or 3 cable sets. Cable length: 30cm
3 pole female XLR cable connector from Neutrik with black metal housing and gold plated contacts.
The cable set SMPS400 is a complete set of cables to connect the SMPS400A180 or the SMPS400A400.
Goldplated binding post to connect your loudspeakers with your amplifier chassis. For banana plug, spade plug and bare wire connections. This binding post can be mounted as a set with the black spacer or as two single connectors.
This on-off switch can be used as a main switch for your amplifier cabinet. This snap-in switch can handle 16A at 230V. The mounting hole is 31 x 11mm and ~ 25mm deep including the faston terminals.
Mains power cable to connect your products with USA and IEC 60320 C13 connection.
50cm balanced signal cable with 4-pin connector also providing the enable signal. Specifications • The QuietConduit cable design incorporates several refinements over normal balanced cables. • A conductive polymer interface layer between the braid shield and the insulation of the signal conductor short-circuits triboelectric currents where they are generating, virtually eliminating microphonic noise pickup. • A secondary benefit of this layer is to improve the electrostatic shielding effectiveness of the braid shield. Another crucial improvement is the elimination of drain wires, which is normally included for ease of termination but which allow shield currents to couple noise asymmetrically into the signal conductors. The geometry of the QuietConduit cable is precisely controlled, insuring that any noise coupling is strictly limited to common mode. Note: This product is manufactured in Hong Kong, while the majority of our products are manufactured in Malaysia, in accordance with the same quality standards.
With this USB cable you can connect the FusionAmp series plate amplifier to your PC.Specifications:USB A - Mini-USB BLength: 1.8 m
The FusionAmp models must be mounted into the speaker cabinet with 8 or 10screws. This set contains 10 self tapping, black, Phillips head screws, 4,3x25mm. Note:This product is manufactured in The Netherlands, while the majority of our products are manufactured in Malaysia, in accordance with the same quality standards.
These spacers can be used with the SMPS400 and UcD3xMP's to ensure that the minimum safety clearance requirements are met. APPLICATIONS • Mounting the SMPS400, UcD32MP, UcD34MP, UcD36MP FEATURES • Weight: 2g • Dimensions: 19.5(10)mm x 6mm • thread: M3 • PCB mounting hole: 4mm • packing quantity: 6 pieces • One metal spacer included
Professional crimping tool with ratchet for insulated solder-less terminals (Red, Blue and Yellow).
Mains power cable to connect your products with IEC 60320 C13 and Euro connection.
This IEC 60320 C14 power connector with fuse holder can be used in your amplifier housing to connect the mains power to your amplifier supply. This power connector is capable to handle 10A at 230V. At the back are Faston terminals for easy connection. The mounting hole must be 32.5x27mm. Fuse not included.